前言

实时钟,英文名RTC(Real Time Clock),在PC里面很常见,在OpenWrt里面却鲜有提及,手头上有一个DS1307的TinyRTC实时钟模块,经过一番折腾,将其融合到了OpenWrt系统,遂将操作过程记录成文.

背景知识

DS1307在最新的OpenWrt中已经提供支持,却没有整合进ramips中,因此,本文的一个重点便是如何为ramips系统配置ds1307.另外,为ds1307编写合适的dts节点也是本文的一个重点.

实现过程

1.为ramips配置ds1307支持

系统在./scripts/medatata.pl中判断并处理RTC_SUPPORT开关,分析之后,原来是在 target/linux/ramips/mt7620/target.mk中,将

原始的内容:

FEATURES+=usb

修改为:

FEATURES+=usb rtc

即可打开mt7620对rtc的支持.

此时,make kernel_menuconfig进入配置菜单.同时应注意,由于ds1307是i2c接口的模块,因此,在device中需要配置i2c的支持.选中i2c之后,便可以在

Device Drivers -> Real Time Clock中看到ds1307

 .config - Linux/mips 3.14.28 Kernel Configuration
 > Device Drivers > Real Time Clock ─────────────────────────────────────
  ┌──── Dallas/Maxim DS1307/37/38/39/40, ST M41T00, EPSON RX-8025 ────┐
  │ CONFIG_RTC_DRV_DS1307:                                            │  
  │                                                                   │  
  │ If you say yes here you get support for various compatible RTC    │  
  │ chips (often with battery backup) connected with I2C. This driver │  
  │ should handle DS1307, DS1337, DS1338, DS1339, DS1340, ST M41T00,  │  
  │ EPSON RX-8025 and probably other chips. In some cases the RTC     │  
  │ must already have been initialized (by manufacturing or a         │  
  │ bootloader).                                                      │  
  │                                                                   │  
  │ The first seven registers on these chips hold an RTC, and other   │  
  │ registers may add features such as NVRAM, a trickle charger for   │  
  │ the RTC/NVRAM backup power, and alarms. NVRAM is visible in       │  
  │ sysfs, but other chip features may not be available.              │  
  │                                                                   │  
  │ This driver can also be built as a module. If so, the module      │  
  │ will be called rtc-ds1307.                                        │  
  │                                                                   │  
  │ Symbol: RTC_DRV_DS1307 [=y]                                       │  
  │ Type  : tristate                                                  │  
  │ Prompt: Dallas/Maxim DS1307/37/38/39/40, ST M41T00, EPSON RX-8025 │  
  │   Location:                                                       │  
  │     -> Device Drivers                                             │  
  │       -> Real Time Clock (RTC_CLASS [=y])                         │  
  │   Defined at drivers/rtc/Kconfig:166                              │  
  │   Depends on: RTC_CLASS [=y] && I2C [=y]                          │  
  │                                                                   │  
  │                                                                   │  
  │                                                                   │  
  ├───────────────────────────────────────────────────────────(100%)──┤  
  │                             < Exit >                              │  
  └───────────────────────────────────────────────────────────────────┘  

2.为ds1307建立dts节点

配置好ds1307的编译开关后,接下来的工作就要在dts里面添加ds1307的设备节点.查阅ds1307的资料,其配置的i2c地址为0x68,因此,dts中可以添加如下内容:

	i2c@0 { 
		compatible = "i2c-gpio";
		gpios = <&gpio2 0 0 /* sda = wan_led*/ 
				&gpio3 0 0 /* scl = wlan_led*/ >; 
		i2c-gpio,delay-us = <10>;	/* ~20 kHz */
		#address-cells = <1>;
		#size-cells = <0>;
		
		rtc@68 { 
			compatible = "dallas,ds1307";
			reg = <0x68>; 
		};
		 
	}; 

系统启动时,可以在TTL中看到如下内容:

[    0.130000] i2c-gpio i2c.4: using pins 40 (SDA) and 72 (SCL)
...
[    0.790000] rtc-ds1307 0-0068: rtc core: registered ds1307 as rtc0
[    0.810000] rtc-ds1307 0-0068: 56 bytes nvram
...
[    0.810000] rtc-ds1307 0-0068: setting system clock to 2015-01-26 22:31:15 UTC (1422311475)

ps:系统自带的hwclock命令可以很方便的对RTC进行相应的操作.

为OpenWrt添加实时钟(RTC)--以MT7620为例