This page describes the features present in OCMock 2.x, using the traditional syntax. All these features, including the selector-based syntax, are available in OCMock 3, too. However, starting with OCMock 3 the default is the modern syntax, described on the new reference page.

Class mocks

id mock = [OCMockObject mockForClass:[SomeClass class]]

Creates a mock object that can be used as if it were an instance of SomeClass.

Expectations and verification

[[mock expect] someMethod:someArgument]

Tells the mock object that someMethod: should be called with an argument that is equal to someArgument. After this setup the functionality under test should be invoked followed by

[mock verify]

The verify method will raise an exception if the expected method has not been invoked.

[mock verifyWithDelay:aDelay]

Stubs

[[[mock stub] andReturn:aValue] someMethod:someArgument]

Tells the mock object that when someMethod: is called with someArgument it should return aValue.

If the method returns a primitive type then andReturnValue: must be used with a value argument. It is not possible to pass primitive types directly.

[[[mock stub] andReturnValue:@YES] aMethodReturnABoolean:someArgument]

Values can also be returned in pass-by-reference arguments:

[[mock stub] someMethodWithReferenceArgument:[OCMArg setTo:anObject]]

[[mock stub] someMethodWithReferenceArgument:[OCMArg setToValue:OCMOCK_VALUE((int){aValue})]]

In this case the mock object will set the reference that is passed to the method to anObject and aValue.

The mock object can also throw an exception or post a notification when a method is called:

[[[mock stub] andThrow:anException] someMethod:someArgument]

[[[mock stub] andPost:aNotification] someMethod:someArgument]

In fact, the notification can be posted in addition to returning a value:

[[[[mock stub] andPost:aNotification] andReturn:aValue] someMethod:someArgument]

The mock can delegate the handling of an invocation to a completely different method:

[[[mock stub] andCall:@selector(aMethod:) onObject:anObject] someMethod:someArgument]

In this case the mock object will call aMethod: on anObject when someMethod: is called. The signature of the replacement method must be the same as that of the method that is replaced. Arguments will be passed and the return value of the replacement method is returned from the stubbed method.

If Objective-C blocks are available a block can be used to handle the invocation and set up a return value:

void (^theBlock)(NSInvocation *) = ^(NSInvocation *invocation) {    /* code that reads and modifies the invocation object */};[[[mock stub] andDo:theBlock] someMethod:[OCMArg any]];

If using a partial mock (see below) it is possible to forward the method to the implementation in the real object, which can be useful to simply check that a method was called:

[[[mock expect] andForwardToRealObject] someMethod]

Note that it is possible to use andReturn:, andThrow:, etc with expect, too. This will then return the given return value and, on verify, ensure that the method has been called.

Class methods

[[[mock stub] andReturn:aValue] someClassMethod]

[[[mock expect] andForwardToRealObject] someClassMethod]

[[[[mock stub] classMethod] andReturn:aValue] aMethod]

[mock stopMocking]

Argument constraints

[[mock expect] someMethod:[OCMArg any]]

Tells the mock object that someMethod: should be called and it does not matter what the argument is. This only works for object arguments.

Pointers and selectors require special treatment:

[[mock expect] someMethodWithPointerArgument:[OCMArg anyPointer]]

[[mock expect] someMethodWithSelectorArgument:[OCMArg anySelector]]

[[[mock expect] ignoringNonObjectArgs] someMethodWithIntArgument:0]

Other constraints available for object arguments are:

[[mock expect] someMethod:[OCMArg isNil]]

[[mock expect] someMethod:[OCMArg isNotNil]]

[[mock expect] someMethod:[OCMArg isNotEqual:aValue]]

[[mock expect] someMethod:[OCMArg checkWithSelector:aSelector onObject:anObject]]

The last constraint will, when the mock object receives someMethod:, send aSelector to anObject and if aSelector takes an argument will pass the argument that was passed to someMethod:. The method should return a boolean indicating whether the argument matched the expectation or not.

If Objective-C blocks are available it is possible to check the argument with a block as follows:

[[mock expect] someMethod:[OCMArg checkWithBlock:^BOOL(id value) { /* return YES if value is ok */ }]];

Last but not least it is also possible to use Hamcrest matchers like this:

[[mock expect] someMethod:startsWith(@"foo")]

Note that this will only work when the Hamcrest framework is explicitly linked by the unit test bundle.

Nice mocks / failing fast

When a method is called on a mock object that has not been set up with either expect or stub the mock object will raise an exception. This fail-fast mode can be turned off by creating a "nice" mock:

id mock = [OCMockObject niceMockForClass:[SomeClass class]]

While nice mocks will simply ignore all unexpected methods it is possible to disallow specific methods:

[[mock reject] someMethod]

Note that in fail-fast mode, if the exception is ignored, it will be rethrown when verify is called. This makes it possible to ensure that unwanted invocations from notifications etc. can be detected.

Protocol mocks

id aMock = [OCMockObject mockForProtocol:@protocol(SomeProtocol)]

Creates a mock object that can be used as if it were an instance of an object that implements SomeProtocol.

Partial mocks

id aMock = [OCMockObject partialMockForObject:anObject]

Creates a mock object that can be used in the same way as anObject. When a method that is not stubbed is invoked it will be forwarded to anObject. When a stubbed method is invoked using a reference to anObject, rather than the mock, it will still be handled by the mock.

The real object can be returned to its original state, i.e. all stubs will be removed:

[aMock stopMocking]

This is only necessary if the original state must be restored before the end of the test. The partial mock automatically callsstopMocking during its own deallocation.

Note that currently partial mocks cannot be created for instances of toll-free bridged classes, e.g. NSString.

Observer mocks

id aMock = [OCMockObject observerMock]

Creates a mock object that can be used to observe notifications. The mock must be registered in order to receive notifications:

[notificatonCenter addMockObserver:aMock name:SomeNotification object:nil]

Expectations can then be set up as follows:

[[mock expect] notificationWithName:SomeNotification object:[OCMArg any]]

Note that currently there is no "nice" mode for observer mocks, they will always raise an exception when an unexpected notification is received.

Instance-based method swizzling

In a nutshell, Method Swizzling describes the replacement of a method implementation with a different implementation at runtime. Using partial mocks and the andCall: stub OCMock allows such replacements on a per-instance basis.

id mock = [OCMockObject partialMockForObject:anObject][[[mock stub] andCall:@selector(differentMethod:) onObject:differentObject] someMethod:[OCMArg any]]

After these two lines, when someMethod: is sent to anObject the implementation of that method is not invoked. Instead,differentMethod: is called on differentObject. Other instances of the same class are not affected; for these the original implementation of someMethod: is still invoked. The methods can have different names but their signatures should be the same.

More detail

The test cases in OCMockObjectTests and OCMockObjectHamcrestTests show all uses of OCMock.

Changes.txt contains a chronological list of all changes.

Features (OCMock 2)