CentOS 6.4 Compiling Xen

一、准备（Prepare） 

需要准备以下文件：
CentOS 6.4-x86_64（安装centos系统）
xen-4.1.2（xen内核源码文件）
linux-3.0.94（linux内核文件）
blktap2-3.0.patch（linux 内核补丁for xen，下载地址：ftp://ftp.enjellic.com/pub/xen/blktap2-3.0.patch）

安装CentOS的步骤此处略过。。。

二、安装

1.关闭SELinux（Disable SELinux）
# vim /etc/selinux/config
chage to SELINUX=disabled
# reboot

2.安装必要的库和软件（Pre-Requirements)

# yum groupinstall "Development tools" "Additional Development" "Debugging Tools" "System administration tools" "Compatibility libraries" "Console internet tools"

# yum install transfig wget texi2html libaio-devel dev86 glibc-devel e2fsprogs-devel gitk mkinitrd iasl xz-devel bzip2-devel pciutils-libs pciutils-devel SDL-devel libX11-devel gtk2-devel bridge-utils PyXML qemu-common qemu-img mercurial texinfo libuuid-devel

# yum install glibc-devel.i686

3.给linux内核打补丁（Patch blktap to kernel）
# cd /path/to/kernel
# patch -p1 < /path/to/patch

4.编译Dom0内核，这里我们用的是Linux（Compile the Dom0 kernel）
# cd path/to/kernel
# make clean
# make mrproper
# make menuconfig (also # vim .config)

下面是需要配置的项，其他项采用默认即可：

Device Drivers --->
[ * ] Block devices --->
<*> Block-device backend driver
Device Drivers --->
-*- Network device support --->
<*> Xen backend network device

Device Drivers --->
XEN driver support --->
[ * ] Xen memory balloon driver
[ * ] Scrub pages before returning them to system
<*> Xen /dev/xen/evtchn device
[ * ] Backend driver support
<*> Xen filesystem
[ * ] Create compatibility mount point /proc/xen
[ * ] Create xen entries under /sys/hypervisor
<*> userspace grant access device driver

General Setup --->
[ * ] Enable deprecated sysfs features to support old userspace tools
[ * ] Enable deprecated sysfs features by default

Device Drivers --->
[ * ] Block devices --->
<*> Blktap userspace devices

# make -j4
# make -j4 modules
# make -j4 modules_install
# make -j4 install

5.编译Xen内核（Compile Xen kernel）
# cd /xen/path
# make world
# make install

6.修改启动项(Configure grub configure)
# vim /etc/grub.conf
Like this:
title CentOS 3.0.94
root (hd0,0)
kernel /....
initrd /....
copy above four lines to before,like this:
title CentOS 3.0.94xen
root (hd0,0)
kernel /boot/xen-4.1.2.gz ( kernel /xen-4.1.2.gz, 看情况而定)
module /...
module /...

Add Xen to start configure：
# /sbin/chkconfig --add xend
# /sbin/chkconfig --add xencommons
# /sbin/chkconfig --add xendomains
# /sbin/chkconfig xend on
# /sbin/chkconfig xendomains on
# /sbin/chkconfig xencommons on

 7.到这里安装完成，重启！

centos源码安装Xen