首页 > 代码库 > IBM P系列小型机更换电池步骤
IBM P系列小型机更换电池步骤
1.查看电池信息
命令：smitty pxdam
选择“ Diagnostics and Recovery Options”
选择“Controller Rechargeable Battery Maintenance”
回车，可以看到电池信息
电池信息各参数含义如下：
battery state：显示电池当前具体状态，有以下几个可能的值
No battery warning/error：No warning or error condition currently exist 这种是电池的正常状态
Warning condition：A warning condition currently exists and an error has been logged 出现了一个警告并被记录在日志中
Error condition：An error condition currently exists and an error has been logged 电池已经出错
Unknow：Information is not available to determine whether a warning or error condition currently exists 无法判断
Power-on time（days）：电池持续使用的天数
Adjusted power-on time（time）：
Indicates the adjusted (prorated) power-on time, in units of days ,of the rechargeable Cache Battery Pack
Note：Some rechargeable Cache Battery Packs are negatively affected by higher temperatures and thus are prorated based on the amount of time that they spend at various ambient temperatures
Estimated（估算的） time to warning（days）:
Estimated time, in units of days, until a message is issued indicating that the replacement fo the rechargeable Cache Bettery Pack should be scheduled
Estimated time to error（days）：当值为0时，此时Cache被自动禁用，必须更换电池
Estimated time , in units of days ,until an error is reported indicating that the rechargeable Cache Bettery Pack must be replaced
Concurrently maintainable battery pack：该电池是否可以在线更换
Indicates that the rechargeable Cache Battery Pack can by replaced while the adapter continues to operate
Battery pack can be safely replaced：当值为YES时，该电池可以安全地更换，不会造成Cache数据丢失
Indicates that the adapter‘s write cache has been disabled and the rechargeable Cache Battery Pack can be safely replaced
2.强制将电池置为Error状态，使写Cache禁用，清空Cache内缓存的数据
命令：smittty pxdam
选择“Force Controller Rechargeable Battery Error”
最好再检查一次，电池信息中“Battery pack can be safely replaced”一项为YES
3.更换电池
注意：必须将旧电池拆下来至少15秒后，再安装新电池，否则PCI-X SCSI RAID卡将不能正常识别电池已更换。
注意：必须确保电池已处于Error状态，才能更换电池，以免Cache中缓存的数据丢失。
根据PCI-X SCSI RAID卡的不同类型，选择Concurrent方式或Non-Concurrent方式更换：
Non-Concurrent方式更换
更换电池必须将卡从机器中拔出
A Battery Pack Casing
B Cache Directory Card
Concurrent方式更换：
更换电池可以在线进行，只需单独将电池拔出，不需要把卡从机器中拔出
4.重新激活写Cache
smitty pxdam
5.清理黄灯告警
输入：diag 回车确认
FUNCTION SELECTION 801002
Move cursor to selection, then press Enter.
Diagnostic Routines
This selection will test the machine hardware. Wrap plugs and
other advanced functions will not be used.
Advanced Diagnostics Routines
This selection will test the machine hardware. Wrap plugs and
other advanced functions will be used.
Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc.)
This selection will list the tasks supported by these procedures.
Once a task is selected, a resource menu may be presented showing
all resources supported by the task.
Resource Selection
This selection will list the resources in the system that are supported
by these procedures. Once a resource is selected, a task menu will
be presented showing all tasks that can be run on the resource(s).
选择“Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc. )”
TASKS SELECTION LIST 801004
From the list below, select a task by moving the cursor to
the task and pressing ‘Enter‘.
To list the resources for the task highlighted, press ‘List‘.
[MORE...9]
Change Hardware Vital Product Data
Configure Reboot Policy
Delete Resource from Resource List
Disk Maintenance
Display Configuration and Resource List
Display Firmware Device Node Information
Display Hardware Error Report
Display Hardware Vital Product Data
Display Multipath I/O (MPIO) Device Configuration
Display Previous Diagnostic Results
Display Resource Attributes
Display Service Hints
Display Software Product Data
Display USB Devices
Display or Change Bootlist
Format Media
Gather System Information
Hot Plug Task
Identify and Attention Indicators
Load ISO Image to USB Mass Storage Device
Local Area Network Analyzer
Log Repair Action
Microcode Tasks
RAID Array Manager
Update Disk Based Diagnostics
Update and Manage System Flash
找到“Log Repair Action”，回车
LOG REPAIR ACTION 801016
Select a resource if it has been replaced recently or has had
corrective actions performed against it. This will update the error
log to prevent diagnostics from performing Error Log Analysis on the
obsolete error log entries for the resource.
To select a resource, move the cursor to the resource and press ‘Enter‘.
To cancel the selection, press ‘Enter‘ again.
Once all selections have been made, press ‘Commit‘.
To avoid selecting a resource, press ‘Previous Menu‘.
sys0 System Object
sysplanar0 System Planar
U787A.001.DPM18T9-
sisscsia0 P1 PCI-X Dual Channel Ultra320 SCSI Adapter
scsi0 P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
hdisk0 P1-T10-L3-L0 16 Bit LVD SCSI Disk Drive (300000 MB)
hdisk17 P1-T10-L8-L0 16 Bit LVD SCSI Disk Drive (73400 MB)
ses0 P1-T10-L15-L0 SCSI Enclosure Services Device
scsi1 P1-T11 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
选择“sys0”，回车确认
To select a resource, move the cursor to the resource and press ‘Enter‘.
To cancel the selection, press ‘Enter‘ again.
Once all selections have been made, press ‘Commit‘.
To avoid selecting a resource, press ‘Previous Menu‘.
+ sys0 System Object
sysplanar0 System Planar
U787A.001.DPM18T9-
sisscsia0 P1 PCI-X Dual Channel Ultra320 SCSI Adapter
scsi0 P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
hdisk0 P1-T10-L3-L0 16 Bit LVD SCSI Disk Drive (300000 MB)
hdisk17 P1-T10-L8-L0 16 Bit LVD SCSI Disk Drive (73400 MB)
ses0 P1-T10-L15-L0 SCSI Enclosure Services Device
scsi1 P1-T11 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
usbhc2 P1 USB Enhanced Host Controller (3310e000)
usbhc0 P1 USB Host Controller (33103500)
usbhc1 P1 USB Host Controller (33103500)
ent0 P1-T5 2-Port 10/100/1000 Base-TX PCI-X Adapter
(14108902)
ent1 P1-T6 2-Port 10/100/1000 Base-TX PCI-X Adapter
(14108902)
fcs0 P1-C4-T1 FC Adapter
fscsi0 P1-C4-T1 FC SCSI I/O Controller Protocol Device
L2cache0 L2 Cache
mem0 Memory
oppanel Operator panel
F1=Help F4=List F7=Commit Esc+0=Exit
F3=Previous Menu
此时，sys0前面出现了一个“+”符号，表示已选中该项
按F7（或ESC+7）提交确认
ESC+0退出
告警清除！
IBM P系列小型机更换电池步骤