首页 > 代码库 > LB集群之LVS/keepalived
LB集群之LVS/keepalived
在上一个实验的基础上LVS/DR
(NTA,DR HA 都是用 nginx 服务操作的，省去了安装nginx安装配置)
lvs虽然已经配置成功也实现了负载均衡，但是我们测试的时候发现，当某台real server把httpd进程停掉，那么director照样会把请求转发过去，这样就造成了某些请求不正常。所以需要有一种机制用来检测real server的状态，这就是keepalived。它的作用除了可以检测rs状态外，还可以检测备用director的状态，也就是说keepalived（集HA+LB于一体）可以实现ha集群的功能，当然了也需要一台备用director.
实验环境：三台虚拟机，10.72.4.48 （dir/master）,10.72.4.39(rs2&slave),10.72.4.37 (rs2)
[root@dir ~]# ipvsadm -C #清空之前的规则
[root@dir ~]# yum install -y keepalived #安装keepalived
[root@dir ~]# vim /etc/keepalived/keepalived.conf
state MASTER #备用服务器上为 BACKUP
interface eth0
virtual_router_id 51
priority 100 #备用服务器上为90
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
10.72.4.100
}
}
virtual_server 10.72.4.100 80 {
delay_loop 6 #(每隔10秒查询realserver状态)
lb_algo wlc #(lvs 算法)
lb_kind DR #(Direct Route)
persistence_timeout 60 #(同一IP的连接60秒内被分配到同一台realserver)
protocol TCP #(用TCP协议检查realserver状态)
real_server 10.72.4.37 80 {
weight 100 #(权重)
TCP_CHECK {
connect_timeout 10 #(10秒无响应超时)
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
real_server 10.72.4.39 80 {
weight 100
TCP_CHECK {
connect_timeout 10
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
}
------------------------------------------------
[root@dir ~]# scp /etc/keepalived/keepalived.conf 10.72.4.39:/etc/keepalived/keepalived.conf #拷贝到从上
[root@rs2 ~]# vim /etc/keepalived/keepalived.conf #只改以下两处，其他地方不都不用改
vrrp_instance VI_1 {
state BACKUP #备用服务器上为 BACKUP
interface eth0
virtual_router_id 51
priority 90 #备用服务器上为90
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
10.72.4.100
}
}
------------------------------------------
[root@dir ~]# /etc/init.d/keepalived start
Starting keepalived: [ OK ]
[root@rs2 ~]# /etc/init.d/keepalived start
Starting keepalived: [ OK ]
[root@rs1 ~]vim /usr/local/sbin/lvs_nat.sh #编译脚本
#! /bin/bash
vip=
10.72.4.100
ifconfig lo:0 $vip broadcast $vip netmask 255.255.255.255 up
route add -host $vip lo:0
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
[root@rs1 ~]sh /usr/local/sbin/lvs_nat.sh #执行脚本
[root@rs2 ~]vim /usr/local/sbin/lvs_nat.sh #编译脚本
#! /bin/bash
vip=10.72.4.100
ifconfig lo:0 $vip broadcast $vip netmask 255.255.255.255 up
route add -host $vip lo:0
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
[root@rs2 ~]sh /usr/local/sbin/lvs_nat.sh #执行脚本
[root@dir ~]# vim /usr/local/sbin/lvs_dr.sh #编译打开dir 上的端口转发脚本
#! /bin/bash
echo 1 > /proc/sys/net/ipv4/ip_forward
[root@dir ~]# sh /usr/local/sbin/lvs_dr.sh #执行脚本
[root@rs2 ~]# /etc/init.d/nginx stop #停掉 rs2 上的nginx ，
Stopping nginx: [ OK ]
#停掉rs2 上的nginx 后，IE 刷新 10.72.4.100，不会再出现rs2 上的内容。且主服务器也会把rs2 的IP 踢除，重新启动rs2 上的nginx 服务，会恢复正常。
--------------------------------------------------------
[root@dir ~]# /etc/init.d/keepalived stop #停掉主dir上的 keepalived ,rs2从上的keepalived就会启动,取代dir 成为主，继续工作。
Stopping keepalived: [ OK ]
再次重新启动主的 keepalived ，就会恢复到之前的状态。
本文出自 “CBO#Boy_Linux之路” 博客，请务必保留此出处http://20151213start.blog.51cto.com/9472657/1885165
LB集群之LVS/keepalived