首页 > 代码库 > 超声波模块SRF05

超声波模块SRF05

2024-07-14 02:37:49   221人阅读

////////////////////////////////////////////////////////////////////////////////
//
//     PIC16F877 + HY-SRF05 + LCD03 example
//     Written October 2008 , using HITECH PIC16 compiler
// 
// Note - assumes a 20MHz crystal, which is 5MHz timer clock
// A 1:4 prescaler is used to give a 1.25MHz timer count (0.8uS per tick)
//
//     This code is Freeware - Use it for any purpose you like.
//
///////////////////////////////////////////////////////////////////////////////




#include <pic.h>
#include <stdio.h>
 
__CONFIG(0x3b32);


#define trig RB0
#define echo RB1


void clrscn(void); // prototypes
void cursor(char pos);
void print(char *p);
void setup(void);
unsigned int get_srf04(void);


char s[21]; // buffer used to hold text to print


void main(void)
{
unsigned int range;


setup(); // sets up the PIC16F877 I2C port
clrscn(); // clears the LCD03 disply
cursor(2); // sets cursor to 1st row of LCD03
sprintf(s,"SRF04 Ranger Test");// text, printed into our buffer
print(s); // send it to the LCD03


while(1) { // loop forever
range = get_srf04();// get range from srf04 (round trip flight time in 0.8uS units)
cursor(24); // sets cursor to 2nd row of LCD03
sprintf(s,"Range = %dcm  ", range/72);// convert to cm
print(s); // send it to the LCD03
cursor(44); // sets cursor to 3rd row of LCD03
sprintf(s,"Range = %dinch  ", range/185);// convert to inches
print(s); // send it to the LCD03


TMR1H = 0; // 52mS delay - this is so that the SRF04 ranging is not too rapid
TMR1L = 0; // and the previous pulse has faded away before we start the next one
T1CON = 0x21; // 1:4 prescale and running
TMR1IF = 0;
while(!TMR1IF);// wait for delay time
TMR1ON = 0; // stop timer
}
}


unsigned int get_srf04(void)
{
TMR1H = 0xff; // prepare timer for 10uS pulse
TMR1L = -14;
T1CON = 0x21; // 1:4 prescale and running
TMR1IF = 0;
trig = 1; // start trigger pulse
while(!TMR1IF);// wait 10uS
trig = 0; // end trigger pulse
TMR1ON = 0; // stop timer

TMR1H = 0; // prepare timer to measure echo pulse
TMR1L = 0;
T1CON = 0x20; // 1:4 prescale but not running yet
TMR1IF = 0;
while(!echo && !TMR1IF);// wait for echo pulse to start (go high)
TMR1ON = 1; // start timer to measure pulse
while(echo && !TMR1IF);// wait for echo pulse to stop (go low)
TMR1ON = 0; // stop timer
return (TMR1H<<8)+TMR1L;// TMR1H:TMR1L contains flight time of the pulse in 0.8uS units
}


void clrscn(void)
{
SEN = 1; // send start bit
while(SEN); // and wait for it to clear


SSPIF = 0;
SSPBUF = 0xc6;// LCD02 I2C address
while(!SSPIF);// wait for interrupt
SSPIF = 0; // then clear it.


SSPBUF = 0; // address of register to write to 
while(!SSPIF);// 
SSPIF = 0; //


SSPBUF = 12; // clear screen 
while(!SSPIF);// 
SSPIF = 0; //


SSPBUF = 4; // cursor off 
while(!SSPIF);// 
SSPIF = 0; //
 
PEN = 1; // send stop bit
while(PEN); //
}



void cursor(char pos)
{
SEN = 1; // send start bit
while(SEN); // and wait for it to clear


SSPIF = 0;
SSPBUF = 0xc6;// LCD02 I2C address
while(!SSPIF);// wait for interrupt
SSPIF = 0; // then clear it.


SSPBUF = 0; // address of register to write to 
while(!SSPIF);// 
SSPIF = 0; //


SSPBUF = 2; // set cursor 
while(!SSPIF);// 
SSPIF = 0; //
SSPBUF = pos; //  
while(!SSPIF);// 
SSPIF = 0; //
 
PEN = 1; // send stop bit
while(PEN); //
}



void print(char *p)
{
SEN = 1; // send start bit
while(SEN); // and wait for it to clear


SSPIF = 0;
SSPBUF = 0xc6;// LCD02 I2C address
while(!SSPIF);// wait for interrupt
SSPIF = 0; // then clear it.


SSPBUF = 0; // address of register to write to 
while(!SSPIF);// 
SSPIF = 0; //


while(*p) {
SSPBUF = *p++;// write the data 
while(!SSPIF);// 
SSPIF = 0; // 
}


PEN = 1; // send stop bit
while(PEN); //
}




void setup(void)
{
unsigned long x;


TRISB = 0xfe; // RB0 (trig) is output
PORTB = 0xfe; // and starts low


TRISC = 0xff;
PORTC = 0xff;


SSPSTAT = 0x80;
SSPCON = 0x38;
SSPCON2 = 0x00;
SSPADD = 50; // SCL = 91khz with 20Mhz Osc


for(x=0; x<300000L; x++);// wait for LCD03 to initialise
}


联系
我们